No results
Card image cap


Purchase Ellab validation equipment and perform validation studies yourself - anytime, anyplace.

Card image cap


Rent Ellab validation equipment and experience the products before committing to a purchase.

Card image cap

On-site Services

Validation and qualification services. IQ/OQ/PQ - Let us do the work!


A warehouse environment may be subject to regulatory compliance, which makes validation and monitoring necessary.


The critical parameters that need to be monitored are usually temperature and humidity. The parameters cannot exceed certain limit values and the variations need to be documented.



After manufacturing and before the dispatch of a pharmaceutical product it needs to be stored in a controlled environment.


The FDA regards Mean Kinetic Temperature (MKT) as a calculation that will show if a product has exceeded storage conditions. MKT can also be used to determine if storage, handling, shipment, etc. have affected the shelf life of the product. The MKT is a calculated fixed temperature that simulates the effects of temperature variations on the product  over a period of time. It expresses the cumulative thermal stress experienced by a product at varying temperatures during storage. In addition to MKT it is recommended that min. and max. values are calculated including a description of the place and time of occurrence.

Get more information

Some of the challenges when validating a warehouse could be:


  • To check the performance of a temperature controlled warehouse
  • To determine the cold and warm zones of the warehouse
  • To confirm pre-defined temperature / humidity ranges
  • To identify and improve temperature / humidity equilibration
  • To determine the highest temperature / humidity fluctuations within the warehouse
  • To revalidate the location of the existing fixed sensors of the current monitoring system
  • To calculate and document the Mean Kinetic Temperature

Continuous Monitoring

Following qualification and validation of warehouses, long-term monitoring solutions can be put into place immediately with Ellab’s environmental monitoring system.


Distribution centres require temperature monitoring in line with global regulations for monitoring of controlled environments and Good Distribution Practices (GDP).


Temperature sensitive products could be in danger if optimum storage temperature levels are not maintained, resulting in the risk of product recalls and loss of reputation. Ensuring temperature integrity during operation provides confidence when storing products in distribution centres.


Pallet positions, loading bays, cold rooms and air-conditioned warehousing can be simultaneously monitored with temperature and humidity wireless data loggers to one comprehensive software platform. Long-range wireless coverage is crucial within these environments to ensure cost-efficiency and gap-free data.



Get more information

hanwell icespy temperature monitoring warehouse


Ellab’s ValSuite software  calculates MKT according to these standards:

  • USP chapter no. 1079: “Good storage and distribution practices for drug products.”
  • ICH norm no. Q1A (R2) page 15.
Get more information


A specified number of loggers are placed in the warehouse in pre-determined critical mapping points. The temperature mapping is typically performed over a minimum period of 48 hours. As an example, the method used for a warehouse validation should take the following points into consideration:

  • Critical mapping points to include outside environment and unconditioned spaces near the measured area
  • Sample rates should be at intervals of every 30 minutes
  • In large areas or spaces it may be necessary to divide the total area in sections and position the specified amount of loggers/sensors in an ‘X’ pattern
  • The data from the mapping activities may be evaluated for conformity or gap analysis
  • All events and movements, including those that are inherent to warehouse operations, should be recorded
  • All test results, observations, evaluations and recommendations should be documented


The frequency of the temperature mapping is a minimum of at least once a year. Additional temperature mapping may be required for changes such as conditions mentioned below:

  • Change of temperature settings
  • Changes made to the storage capacity
  • New monitoring system
  • New equipment installed that may impact the temperature and relative humidity
  • If the continuous temperature mapping activities are interrupted (e.g. due to power failures or any event that may impair the continuous data collection)
  • Extreme weather changes
  • Warehousing standards or quality management system changes
  • Any other changes made that could affect temperature/humidity
Find the products for you

In areas with potentially high temperature fluctuations additional temperature recording devices must be strategically located:

  • Near windows, ceilings and exits
  • Skylights, air-blowers, ducts and A/C units
  • Areas with high traffic movement and activities
  • Near heat sources


The temperature mapping grid should have all temperature recording devices and loggers positioned at distances following the sensor’s capacity to efficiently measure the temperature changes across the entire warehouse. The mapping grid should allow the thermal mapping activity to capture both the hot and the cold zones. The distance between the sensors should ensure that the thermal mapping activity will be able to record and produce an efficient temperature profile of the warehouse.


Warehouse Validation Challenges

ValSuite® Software Reports


Card image cap
Process Graph
download pdf
Card image cap
download pdf
Card image cap
Mean Kinetic Temperature Report
download pdf